Selection Guide · 9 min read
Nichrome Wire VS FeCrAl Wire: How to Choose
On this page
Both families exist to turn electricity into heat. They fail in different ways, at different temperatures, at different prices. Choosing wrong usually costs nothing in the first month and a lot in the third year. We are the factory that draws both families on the same line, so the comparison below is measured, not marketing.
The two families at a glance
Nichrome is a nickel-chromium alloy — Ni80Cr20, Ni60Cr15, Ni35Cr20 in our range. FeCrAl is iron-chromium-aluminium — 0Cr25Al5, 0Cr21Al6, 0Cr27Al7Mo2. The aluminium is the whole point: it grows a protective alumina scale that lets FeCrAl run hotter than any nichrome.
| Property | Nichrome (Ni80Cr20) | FeCrAl (0Cr25Al5) |
|---|---|---|
| Max temperature in air | 1,200 °C | 1,300 °C (0Cr27Al7Mo2: 1,400 °C) |
| Resistivity | 1.09 ±0.05 µΩ·m | 1.42 µΩ·m |
| Density | 8.4 g/cm³ | 7.15 g/cm³ |
| Ductility after service | Good — elements can be re-bent | Poor after first firing — brittle |
| Atmosphere tolerance | Better in reducing / low-oxygen gas; life still derates | Needs oxygen to build the alumina scale |
| Chloride / reducing media | Better | Alumina scale breaks down |
| Cost per kg | High (nickel) | Low (iron base) |
Table 1. Nichrome 80/20 against FeCrAl 0Cr25Al5 on published reference values. Element temperatures, not furnace setpoints; confirm grade equivalence by chemistry and standard number.
Where nichrome wins
- Cyclic and handled elements. Nichrome keeps its ductility after firing, so it survives vibration, handling and occasional re-bending.
- Reducing or low-oxygen atmospheres. FeCrAl cannot rebuild its alumina scale without oxygen, so it degrades quickly in hydrogen, cracked ammonia, carbon-bearing gas or vacuum. Nichrome is the better of the two there — but its own life still falls well below the air rating, so derate the surface load rather than assuming the headline temperature applies.
- Appliance and visible elements. Better oxidation colour control and predictable behaviour at moderate surface loads.
Where FeCrAl wins
- Above 1,200 °C. There is no nichrome grade that runs there.
- Cost per kilowatt-hour. Higher resistivity means less metal for the same wattage, and iron-base chemistry is cheaper per kilogram.
- Long static runs. Industrial furnace elements that are installed once and left alone are the ideal FeCrAl case.
The decision rule
Above 1,200 °C: FeCrAl, no discussion. Below that, ask one question: will anyone touch, bend or vibrate this element after it has been fired? If yes, nichrome. If the element is installed once and never handled, FeCrAl usually gives the same life for less money.
One more trap
Do not switch families without re-sizing the element. Resistivity differs by about 30% and density by about 15% — the same winding geometry with the other family is a different wattage. Send us power, voltage and geometry and we will size the replacement before you order.
Key takeaways
- Above 1,200 °C the choice is already made. No nichrome grade is rated for sustained service there. FeCrAl is the only option.
- Ductility after firing is the real divider. Nichrome survives handling, bending and vibration. FeCrAl turns brittle after its first firing.
- Never swap families without re-sizing. Resistivity differs by roughly 30% and density by 15% — the same winding gives a different wattage.
- Atmosphere matters as much as temperature. FeCrAl needs oxygen to rebuild its alumina scale; reducing gas or vacuum shortens its life sharply.
Frequently asked questions
Can I replace a nichrome element with FeCrAl at the same dimensions?
No. FeCrAl resistivity is about 30% higher and density about 15% lower, so the same wire diameter and length produce a different wattage. Re-size the element before ordering, or specify power, voltage and geometry and let the sizing follow from those.
Which is better in a vacuum furnace?
Neither performs at its air rating. FeCrAl cannot rebuild its alumina scale without oxygen and degrades quickly; nichrome also loses life but is the more tolerant of the two. For sustained vacuum service, derate the surface load substantially and consider molybdenum or tungsten elements above 1,300 °C.
Does FeCrAl really become brittle?
Yes. After the first high-temperature firing the aluminium-rich surface layer makes the wire brittle at room temperature. It is fine in service, but it cannot be re-bent or straightened afterwards — plan the installation so the element is never handled again.
Is nichrome more expensive per kilowatt-hour of service?
Not necessarily. Per kilogram it costs more, but the comparison that matters is cost per finished element that reaches its expected life. In cyclic, handled or reducing-atmosphere service, a cheaper FeCrAl element that fails early is the more expensive choice.
Can nichrome survive short excursions above its 1,200 °C rating?
Short excursions above the rated maximum accelerate oxidation and grain growth even if the element survives. Treat them as consuming life, not as free headroom, and reduce the surface load if the cycle repeats.
Next step
Send three numbers, get an answer
Diameter or cross-section, working temperature, and required power or resistance. We reply within 24 hours with the grade that fits, and with where the margin sits.
