Skip to content
Home / Products / Heating & Resistance
Product category 03

Heating & Resistance Alloy Wire — Factory Direct

Two families, one purpose: predictable resistance at temperature. FeCrAl for the highest element temperatures and lowest cost per kilowatt-hour; nichrome for strength, ductility and the widest availability.

5product series
0.02–10 mmdiameter range
1,400 °CFeCrAl ceiling
±3%resistivity band

Products in this category

Each series is a separate page with grades, tolerances, forms and packing.

Grades and typical applications

Indicative data — the order confirmation carries the binding specification.

GradeUNS / GBKey dataTypical use
0Cr25Al5FeCrAl1.42 µΩ·m · 1,300 °CGeneral furnace elements, lowest cost per kg
0Cr21Al6FeCrAl1.23 µΩ·m · 1,250 °CAppliance and oven elements
0Cr21Al6NbFeCrAl + Nb1.45 µΩ·m · 1,350 °CBetter hot strength, less sag in long elements
0Cr27Al7Mo2FeCrAl + Mo1.53 µΩ·m · 1,400 °CHighest temperature, ceramic fibre modules
Ni80Cr20Nichrome1.09 ±0.05 µΩ·m · 1,200 °CGeneral purpose elements, best ductility
Ni60Cr15Nichrome1.12 µΩ·m · 1,150 °CCost-driven elements with good oxidation resistance
Ni35Cr20Ni-Cr-Fe1.04 µΩ·m · 1,100 °CDomestic appliances, lower nickel content
Ni70Cr30Nichrome1.18 µΩ·m · 1,200 °CHigher resistivity nichrome for compact elements and long life
Constantan CuNi44Cu-Ni0.49 µΩ·m · low TCRShunts, resistors, thermocouple legs
Manganin CuMn12NiCu-Mn-Ni0.43 µΩ·m · ±10 ppm/KPrecision resistors, calibration standards

How to choose

Three questions that decide the grade before price is discussed.

FeCrAl or nichrome?

FeCrAl wins on temperature (up to 1,400 °C), resistivity and price. Nichrome wins on ductility after service, on strength at temperature, and on behaviour in reducing or vacuum atmospheres where the alumina scale of FeCrAl cannot form properly. Above 1,200 °C, there is no nichrome option.

Calculate the wire before you choose the grade.

Resistance per metre fixes the wire length for a given wattage. A higher-resistivity grade means a shorter, thicker wire — often cheaper and stronger. Send us power, voltage and element geometry and we will size it with you.

Plan for the oxide, not just the metal.

Every element grows a scale. FeCrAl grows alumina, which is protective but brittle when cold; nichrome grows chromia, which spalls on thermal cycling. Winding, support spacing and start-up procedure all affect service life more than grade alone.

Quality documents with every lot

01

Heat traceability

Coil and spool numbers linked to the melt.

02

EN 10204 3.1

Chemistry, mechanicals, dimensions.

03

Certificate of conformity

Against the agreed standard.

04

Third-party inspection

SGS, BV or TÜV on request.

Questions buyers ask before ordering

Why does FeCrAl wire become brittle?

Aluminium in the alloy forms a protective alumina scale. After the first firing, the wire loses most of its room-temperature ductility, so elements must be designed not to need re-bending after installation. Grain growth at high temperature adds to the effect.

Can you supply to my resistance per metre?

Yes. We hold resistivity within ±3% on request and can certify resistance per metre or per kilogram. For element production this is usually more useful than a diameter tolerance alone.

What is the maximum operating temperature in air?

0Cr25Al5 to 1,300 °C, 0Cr27Al7Mo2 to 1,400 °C, Ni80Cr20 to 1,200 °C, Ni60Cr15 to 1,150 °C. In reducing atmospheres or vacuum these limits drop sharply — tell us the atmosphere, it changes the answer.

Do you supply flat and stranded forms?

Yes: flat strip from 0.1 × 0.8 mm, and stranded or braided constructions for flexible leads. Stranded conductors are quoted with the equivalent cross-section and resistance per metre.

Ready to specify Heating & Resistance?

Send the grade, size, quantity and service conditions. An engineer replies within 24 hours with a quotation and, if useful, a grade recommendation.

WhatsApp UsContact Us