Best Alloy Grade for Industrial Furnace Heating Elements
0Cr25Al5 vs 0Cr21Al6Nb vs 0Cr27Al7Mo2 vs nichrome — mapped by furnace type, temperature and atmosphere.
Each family is stocked as drawn wire, flat wire and rod — in the grades your drawing, or your cross-reference sheet, already asks for.
Ni200 / Ni201 drawn wire and strip for vacuum components, battery tabs, electronic leads and caustic service. Low gas content, clean bright surface.
Superalloy and corrosion-resistant grades for furnace fixtures, chemical plant, heat exchangers and high-temperature fasteners.
FeCrAl, nichrome and copper-nickel resistance wire for industrial furnaces, appliance heating elements and precision resistors.
Nickel-based, nickel-copper and stainless filler metals in TIG, MIG and SAW form — spooled to your wire-feed specification.
Founded in 2018 in Jiangsu, our 12,000 m² plant draws, bright-anneals, spools and tests alloy wire in a single continuous flow — so a change of grade never leaves the building, and the certificate matches the spool in your hand.
Multi-pass drawing on wet and dry lines, 0.02 mm to 10 mm, with in-line diameter feedback on every pass.
Continuous bright annealing under protective atmosphere to hold resistivity, elongation and an oxide-free surface.
Resistivity, tensile and dimensional checks, then spooled to your weight, bore and labelling requirement.
Most alloy wire problems are not metallurgy problems — they are handover problems between mill, trader and drawing line. We removed the handovers.
ISO 9001:2026 · EN 10204 3.1 material test report with every shipment.
FeCrAl, nichrome, pure nickel, nickel alloys and welding wire from one plant — one origin, one test report, one shipment to clear.
Fine-wire capability with controlled ovality and a clean surface, so fine elements and small-diameter leads behave the same on every spool.
Incoming billet check, in-process diameter control, final resistivity and tensile test — recorded against the heat number you receive.
Standard grades from 10 kg, repeat production to tonnage without re-qualifying a new supplier halfway through the project.
Buyers in Europe, North America and Southeast Asia qualify us on paperwork first. Here is what ships with the spool.
Documented process control from incoming billet to final inspection and packing.
Mill test report with heat number, chemistry and mechanical results for every shipment.
Declarations prepared for EU-bound heating, electronic and battery component orders.
Engineers map your existing grade number to an equivalent we draw, test and stock.
Heat that does not vary, resistance that does not drift, and a surface that does not fail early.
FeCrAl and nichrome elements for roller hearth, tempering, annealing and sintering furnaces.
Precision nichrome for hair dryers, ovens, toasters, fan heaters and cartridge heaters.
Pure nickel wire and strip for vacuum components, battery tabs and electrode parts.
Stable resistance wire for sealing bars, hot-cut knives and form-fill-seal packaging lines.
Long-run furnace users, distributors and equipment builders — the ones who re-order.
“We replaced an imported FeCrAl grade with 0Cr25Al5 from this plant. Eleven months of furnace running, no unexpected shutdowns, same heating performance at 38% lower procurement cost.”
“Diameter and resistivity matched the certificate on every delivery. That is what we actually buy — a spool we do not have to re-check before it goes on the line.”
“They mapped our old grade number to their equivalent and had trial spools out in ten days. Far easier than qualifying a new mill from scratch.”
Grade selection, failure analysis and cost comparison — written for the engineer who has to sign off the specification.
0Cr25Al5 vs 0Cr21Al6Nb vs 0Cr27Al7Mo2 vs nichrome — mapped by furnace type, temperature and atmosphere.
Temperature limits, oxidation behaviour, ductility after service and cost — with a decision table.
Surface load, thermal cycling, atmosphere and support contact — what actually kills elements.
The five questions buyers and engineers ask us most — answered with the numbers we actually work to.
For standard spool alloy wire, spools start at 5 kg for fine sizes and 25 kg for standard element diameters; typical production orders run 50–100 kg. Large-diameter special alloy wire can be ordered from 10–20 kg. For fully customised non-standard grades, talk to our sales team.
Common standard alloy grades: 2–3 weeks after order confirmation. Special or custom alloy formula: 4–6 weeks. Priority production can be arranged for urgent projects.
Yes — custom spool labels, special packaging, custom tolerance, special surface treatment and custom alloy formula. We can produce to your drawing or technical specification sheet.
Our factory holds ISO 9001:2026 certification. Every shipment can be accompanied by a material test report (MTR) and certificate of conformity.
T/T and L/C. General trade term: 30% deposit after order confirmation, balance against copy of shipping documents.
Send the grade number and the property you rely on — resistivity, max temperature or chemistry. We cross-reference to a GB / ASTM / EN equivalent and confirm with trial spools.
Tell us the grade, diameter and quantity — or send the drawing you already have. An engineer reviews it, and you get a factory-direct quotation with lead time inside 24 hours.